WorkSafe Routine Hoist Inspections
Certified Annual Periodic Safety Audits Aligned with Australian Standard AS 2550.9:2018
Under Western Australian WorkSafe occupational health and safety regulations, all commercial vehicle hoists must undergo documented periodic safety inspections by qualified, competent technicians at intervals not exceeding 12 months. P&M Automotive Equipment provides fully certified periodic audits across Perth, Maddington, Welshpool, Canning Vale, Wangara, Bunbury, Kalgoorlie, and the Pilbara.
What Our Certified Technicians Inspect & Deliver
Vehicle hoists are safety-critical industrial lifting equipment. Failure of a cable, hydraulic seal, or mechanical arm restraint can lead to catastrophic workshop accidents, severe injury, or crushing damage to customer vehicles. Operating an uncertified or overdue hoist can also void commercial workshop liability insurance and invite immediate prohibition notices from WorkSafe WA inspectors. P&M Automotive Equipment delivers rigorous, factory-backed inspections that examine every structural, mechanical, and hydraulic component to ensure total legal compliance and peak bay productivity.
Inclusions & Physical Inspection Checkpoints
- Wire rope balance cable tension, strand wear, deformation, and terminal end security
- Hydraulic power unit relief valve pressure verification, cylinder rod condition, and seal integrity
- Mechanical safety lock carriage engagement, spring return, and dual-column synchronization
- Arm restraint gear teeth mesh, positive lock engagement, and anti-slip pin security
- Overhead limit shut-off microswitches and electrical conduit protective integrity
- Concrete floor slab chemical anchor torque verification (AS 2550.9 pull-out compliance)
- Rubber lift pad condition, height adapter extensions, and 4WD chassis saddle integrity
- Formal sign-off in the on-site equipment logbook and issuance of digital WorkSafe certification
Why Annual AS 2550.9 Inspections Are Essential for WA Workshops
In Western Australia, regulatory enforcement around vehicle lifting equipment has tightened significantly. WorkSafe WA inspectors routinely visit automotive dealerships, independent mechanical bays, tyre franchises, and fleet service depots across Perth, Osborne Park, Wangara, and regional centers to verify hoist logbooks and inspection certificates.
Under AS 2550.9 Clause 9.2, periodic inspections must be performed by a 'competent person' who has received formal training and possesses the technical expertise to identify microscopic fatigue, hydraulic pressure degradation, and cable wire rope wear. Simply lubricating the sliders and checking the fluid level is not sufficient. Our P&M technicians carry calibrated tension gauges, magnetic testing equipment, and laser alignment tools to perform comprehensive physical and dynamic load assessments.
Our inspection route covers the entire state: from metropolitan hubs like Welshpool, Malaga, and Rockingham, down to the South West (Bunbury, Busselton, Margaret River), out east through the Goldfields (Kalgoorlie-Boulder), and up north to resource workshops in Karratha, Port Hedland, and Newman. Because we stock genuine replacement parts in our Maddington warehouse, our mobile vans can rectify common safety deficiencies on the spot, avoiding prolonged bay closures.
Serving all Western Australian trade areas: Perth Metro (Maddington, Canning Vale, Welshpool, Wangara, Osborne Park, Malaga, Rockingham), South West (Bunbury, Busselton, Collie, Albany), Goldfields (Kalgoorlie, Leonora), Mid West (Geraldton), and the Pilbara (Karratha, Port Hedland, Newman).
Book Routine Compliance Inspections
Our factory-trained technicians service commercial trade workshops across Perth, the South West, Goldfields, and the Pilbara.
5% Discount on Hoist Replacements
If our inspection reveals that your hoist has reached end-of-life, regular service clients receive an exclusive 5% discount on a brand new replacement hoist from our warehouse.
Why Trust P&M for Routine Compliance Inspections
Full WorkSafe WA Legal Protection
Receive signed, accredited compliance documentation meeting WorkSafe WA requirements and safeguarding your workshop against liability claims.
Pre-Empts Costly Catastrophic Bay Failures
Identifies early cable fraying, hydraulic pressure drop, and carriage slider wear before a customer's vehicle becomes trapped in the air.
Fast On-The-Spot Part Rectification
Our mobile technicians carry genuine replacement cables, safety switches, and hydraulic seals to fix minor faults immediately during the audit.
Our 3-Step Service Process
Visual & Structural Examination
Physical inspection of columns, welds, baseplates, carriage pulleys, and concrete slab anchorage using calibrated measuring tools.
Dynamic Operational & Lock Testing
Testing ascent and descent speeds, emergency descent release valves, arm restraint interlocks, and overhead safety cut-off switches under simulated load.
Logbook Sign-Off & Compliance Certification
Issuance of the formal WorkSafe compliance certificate, updating your workshop register, and providing clear advisory on future wear intervals.